Sea-doo GTX supercharger rebuild

We have been cracking on with the wetlev,  as the season is coming to a start we thought it would be best to rebuild the supercharger on the 2006 Sea-Doo GTX jetski.

First thing to do was remove the supercharger – this is very simple and should take you about 1-2 hours.  There lots off guides on the internet a quick search on the internet will provide many guides but a quick teardown is

  • Remove seats
  • Remove engine bay trims
  • Remove inlet pipes
  • Remove boost pipe
  • Unbolt exhaust manifold and disconnect water pipe
  • Remove exhaust waterbox strap
  • Relocate exhaust
  • Remove 3 bolts for supercharger and then slide supercharger out

Once the supercharger is out you should see some thing like this:

The supercharger once removed

The supercharger once removed

I made a bracket to support the charger in the vice:

Bracket made to hold the supercharger in the vice

Bracket made to hold the supercharger in the vice

The important part is the gear drive with clutch unit:

The supercharger drive unit and clutch

The supercharger drive unit and clutch

First job is to grind down a 25mm spanner so it fits on the flats next to the gear, undo the 17mm nut the thread is a normal right hand thread.  Once the nut is undone remove the sleeve and the dished washers that are part off the clutch unit. You then remove the first clutch washer, followed by the driver gear and needle bearings followed by the second clutch washer.  Once all removed turn the supercharger round and we will start on the input side.

Remove all but 2 off  the bolts around the outside off the supercharger unit, I then split the casing in 2 by pressing wedges between the lugs that stick around the outside once the casing has come apart remove the final bolts and separate.

The inside off the drive side off the supercharger

The inside off the drive side off the supercharger

 

After splitting the supercharger into half

After splitting the supercharger into half

Now refit the 25mm locking ring on the back off the supercharger and using a 17mm socket undo the supercharger impeller (this thread is Left hand so turn clockwise to undo) once undone remove the washer and the impeller and mounting base plus O ring.

The inside off the drive side off the supercharger

The inside off the drive side off the supercharger

Inspect the impeller for damage this one looked very good.

The vanes look in very good condition

The vanes look in very good condition

Vanes removed

Next job is to press the shaft out off the supercharger housing. I sat the charger on so aluminium blocks and used a drill press to press the shaft out (the shaft came out quite easy with the bearing attached)

Placed on aluminium blocks

Placed on aluminium blocks

Using the pillar drill as a press

 

The bearing came out with the shaft

Now comes the part you need a special tool for,  You need to remove the round aluminium cover that is the inner bearing cover.   Because I dont have any special tools I made my own version.  Using some 6mm steel plate I marked a 44mm diameter circle, I then marked a cross through the center off the circle then drilled a 6mm hole at each intersection point using a 6mm shanked bolt with the head cut off and using 2 nuts to hold it into the plate.  I then welded an old wheel nut to the other side.

6mm Steel plate with 4x6mm studs in a 44mm diameter circle

6mm Steel plate with 4x6mm studs in a 44mm diameter circle

The back side off my homemade tool - 19MM wheel nut welded to the back

The back side off my homemade tool – 19MM wheel nut welded to the back

After heating the supercharger housing to release the loctite the tool was used to undo the cover

Home made tool

This cover proved to be very tight and took 2-3 attempts off heating and trying to get it undone.

Supercharger housing

DSC00659

 

DSC00660

At this stage with everything removed I clean both sealing faces on the supercharger and also completely cleaned all the housings

Next was to reinstall the bearing under the cover

DSC00661

 

Reinstall the bearing cover and using a drill bit I placed the shaft support in the back half (This stage was not needed as the main shaft and other bearing should be built as unit and pressed into this bearing)

 

DSC00662

 

Press the bearing onto the shaft and fit all the sleeve’s and spacers in the order they came out, Now press the complete assembly into the supercharger and other bearing

DSC00667

 

Now you should end up with this sticking out

DSC00668

Press the new seal in and fit the O ring and impeller mounting flange

DSC00669

Now refit the impeller (remember nut is Left hand thread) and torque to correct setting.  Now apply a very thin film off sealer around the edge off the supercharger (most people use way to much and anything that squibs out will squib inside as well and go round the engine!!)

DSC00673

DSC00674

 

Now bolt both sections back together

DSC00675

 

A very very slight squib 🙂

Now we start  back on the drive side off the supercharger, start by soaking the new supercharger washers with oil and install 1 onto the shaft.

DSC00676

 

I used a socket to act a press for installing the needle washers into the drive gear

DSC00678

DSC00679

I then very carefully installed the drive gear onto the shaft taking care not to loose and needles rollers

DSC00680

I popped some more oil on the needles rollers and installed the other washer

Reinstall the locking tab and clutch washers in the order shown on the sheet, fit the nut and torque the nut.

DSC00682

 

Now lock the drive pulley and using the torque wrench set to 8nm and check the torque wrench clicks before the clutch slips

Now set the torque wrench to 14nm and check the clutch slips before the torque wrench clicks.  If yes (which it should) then great if not recheck your spring washers.

Reinstall the 2 rubber O rings and refit the charge and enjoy!

 

 

 

 

 

  1. Steve Reply

    Hi – have you ever heard of folks initialling a washer in between the SC and the engine at the three bolt locations ? Being advised to do it, but seems very odd…
    tks man
    Steve

    • Toby Gardner Reply

      You only need to install washers under the supercharger mounting it you fit the later shaft (the rebuilt kit my guide shows fitting) into the early housing. The supercharger I rebuilt was a 2006 model and didn’t need the spacers but I think pre 2005 need the washers adding.

  2. William Hill Reply

    Thank you for that run through. You seem very knowledgeable about the charger and must applause you for A most helpful presentation. Thank You!! Lots of people talk A bunch of gibber jabber,only wanting to be seen on the web actually looking and sounding,they think “full of knowledge”” but to someone with experience they sound like Baffoons. Its nice to find someone that knows what he is talking about on the web finally. Again Thank You.

Leave a Reply to William Hill Cancel reply

*